Optimization of Burr size, Surface Roughness and Circularity Deviation during Drilling of Al 6061 using Taguchi Design Method and Artificial Neural Network
Main Article Content
صندلی اداریAbstract
This paper presents the influence of cutting parameters like cutting speed, feed rate, drill diameter, point angle and clearance angle on the burr size, surface roughness and circularity deviation of Al 6061 during drilling on CNC vertical machining center. A plan of experiments based on Taguchi technique has been used to acquire the data. An orthogonal array, signal to noise (S/N) ratio and analysis of variance (ANOVA) are employed to investigate machining characteristics of Al 6061 using HSS twist drill bits of variable tool geometry and maintain constant helix angle of 45 degrees. Confirmation tests have been carried out to predict the optimal setting of process parameters to validate the used approach, obtained the values of 0.2618mm, 0.1821mm, 3.7451µm, 0.0676mm for burr height, burr thickness, surface roughness and circularity deviation respectively. Finally, artificial neural network has been applied to compare the predicted values with the experimental values, good agreement was shown between the predictive model results and the experimental measurements.
Downloads
Article Details
1. Proposal of Policy for Free Access Periodics
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 that allows the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in an institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
Proposal of Policy for Periodic that offer Postponed Free Access
Authors whom publish in this magazine should agree to the following terms:
a. Authors should keep the copyrights and grant to the magazine the right of the first publication, with the work simultaneously permitted under the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 [SPECIFY TIME HERE] after the publication, allowing the sharing of the work with recognition of the authorship of the work and initial publication in this magazine.
b. Authors should have authorization for assuming additional contracts separately, for non-exclusive distribution of the version of the work published in this magazine (e.g.: to publish in institutional repository or as book chapter), with recognition of authorship and initial publication in this magazine.
c. Authors should have permission and should be stimulated to publish and to distribute its work online (e.g.: in institutional repositories or its personal page) to any point before or during the publishing process, since this can generate productive alterations, as well as increasing the impact and the citation of the published work (See The Effect of Free Access).
d. They allow some kind of open dissemination. Authors can disseminate their articles in open access, but with specific conditions imposed by the editor that are related to:
Version of the article that can be deposited in the repository:
Pre-print: before being reviewed by pairs.
Post-print: once reviewed by pairs, which can be:
The version of the author that has been accepted for publication.
The editor's version, that is, the article published in the magazine.
At which point the article can be made accessible in an open manner: before it is published in the magazine, immediately afterwards or if a period of seizure is required, which can range from six months to several years.
Where to leave open: on the author's personal web page, only departmental websites, the repository of the institution, the file of the research funding agency, among others.
References
DAVIM, J. P.; REIS, P. (2003) Drilling carbon fiber reinforced plastic manufactured by auto clave experimental and statistical study. Materials and Design, v. 24, n. 5, p. 315-324,
FURNESS, R. J.; WU, C. L.; ULSOY, A. G. (1996) Statistical analysis of the effects of feed, speed, and wear of hole quality in drilling. Journal of Manufacturing Science and Engineering, v. 118, n. 3, p. 367-375
KURT, M.; BAGCI, E.; KAYNAK, Y. (2009) Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. International Journal of Advanced Manufacturing Technology, v. 40, n. 5-6, p. 458-469
NALBANT, M.; GOKKAYA, H.; SUR, G. (2007) Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning. Materials and Design, v. 28, n. 4, p. 1379-1385.
TSAO, C. C.; HOCHENG, H. (2008) Evaluation of thrust force and surface roughness in drilling composite material using Taguchi analysis and neural network. Journal of Materials Processing Technology, v. 203, n. 1-3, p. 342-348.
YANG, J. L.; CHEN, J. C. (2001) A systematic approach for identifying optimum surface roughness performance in end-milling operations. Journal of Industrial Technology, v. 17, n. 2, p. 1-8.